Dedicated to Supplying the Finest Slot Racing Products to Clients Worldwide
Get Your ready to run with a couple of easy clicks;-
The chassis comes built with Soldered brass pin tubes, Refaced, aligned oilite bushings, HR60 drill blank axle, guide, JK Tri-pin guide nut, silver plated guide clips, braids and Lead wires installed for just £35.30
Then add you choice of motor;- Falcon 7, JK Hawk 7, JK Hawk Retro or for G12, our 46 degree proslot motor complete with brush shunts and can ballrace.
Pick your gear ratio and it’s job done! (64 pitch gears have JK “thin” spurs for FK Racing, 72 pitch have angled spurs.
JK X32 Chassis £20.25
The J-bar Accessory Pack is in stock now. Part number is JKC26J. A pack of 6 bars:
The TSRF Wood track Guide flag, 1/8” post and accepts folded,conventional, clipped braids. A great guide flag for when minimum space is available at the front of the car. £2.45
JK GTB Guide Tongue Brace
Legal for UKRRA on all “coined” brass chassis £2.55 (not legal for BSCRA !)
JK C62 1/32 F1 chassis kit in Stainless steel. £21.25
A Quality Kit, complete which everything you need to build a great car. The kit comes with JK Hawk Retro motor, 11/37 gear ratio and polymer, reverse hub JK B tyres, rear axle bushings, HR60 drill blank rear axle, front wheel stickers, lead wire guide, guide nut and silver plated guide clips, braids, body mounting pins.
Please note these are usually in stock subject to chassis availability.
Black flexible Silicon rubber strip, just 0.5mm thick and 6mm wide with an Ultra High Bond tape backing.
Length 200mm. Provides damping of chassis pans (which is adjustable in regard to movement dependant on location of use between pan & centre section). £1.80 per strip
ALL NEW MOSSETTI CAN - AM KIT
2018 Mossetti Can-Am kit in brass. (Please note these kits come with the narrow spring steel guide plate, legal for UKRRA).
PRO-AM 1/24th Kit. AB G12 chassis complete with piano wire, pin tube, centre spine ferrules & complete instruction sheet. Choice of JK Hawk 7, JK Hawk Retro or Falcon 7 motor. Choice of gear ratios with 11 or 12 /37 in 64 pitch. HR60 drill blank axle, rear axle ballraces, guide, guide clips, braids, guide nut, lead wire, JK sticker front wheels, Koford Short pins, Body armour, JK Rear wheels and JK Lola body. Only £63.00 (postage added at check out).Only at www.abslotsport.biz Click your preferences, pay by Paypal and get it in the next post!
AB 1/32 F1 Kit for FK motors.
NOW WITH PRE CUT 1.5MM brass pans!
The stongest, dominating chassis in Pro-Am, easy to build, Reversible pan hangers for steel or brass pans.
Falcon Pro 1/32 sports chassis. Super easy build, tough and
Consistently a winner!
Micro Reversible brackets may be built for inline gear mesh (motor shaft to rear axle center) or offset to allow for a 1mm offset between motor shaft and rear axle centres.
Suitable for all “Micro motors” including beardog motor. Standard micro bracket £3.40
XL Micro Bracket with longer side leg spacing for use with larger crown gears (2mm longer than the Std bracket) £3.60
Midi Reversible bracketsmay be built for inline gear mesh (motor shaft to rear axle center) or offset to allow for a 1mm offset between motor shaft and rear axle centres.
Suitable for all FK type motors
1/32nd scale injection moulded Driver Heads are back! We found the box! Great quality injection mouldings Just £1.50 each. When they are gone - they are gone!
ARP Double Ballrace Fronts for Cam-Am, narrow profile hub, suits the New Mossetti chassis £19.50
JK C92 sidewinder bracket. Drilled for FK motor mounting. May be used as a scratch build bracket for Scale or Drag racing and also adapted for use as a “bolt in bracket” for FK motors in angelwinder Production chassis. £2.90.
Piano wire in nominal 12” lengths.
0.032” @ 0.65p
0.047” @ 0.70p
0.055” @ 0.81P
0.062 @ 0.89p
K&S Brass tube available in the following sizes, 12” lengths.
1/16” OD (0.032” id for pin tube) £2.90
3/32” OD (0.062” id for 16G wire) £3.10
1/8” OD (3/32” id for 3/32” axles) £4.10
7/32” OD (for 3/16” x 3/32” bushings and ballraces) £4.40
K&S square tube. Great for pin tubes. pivots and sliders when soldering to the edge or surface of brass plate.
1/16” (0.034 inside) for use with 0.032” wire & Pins